problem with M3414 chainsaw
Gidday, Got problem with a M3414 chain saw. It runs for about 3 to 4 minutes then cuts out and will restart after a minute or so. I put a spark tester on it and watched it run, there was no problem...
View ArticleClik here to view.
Mcculloch 170AWFPX ?
Hi all Newbie here... just said a quick hello in New members Area... I recently acquired this machine and if im honest pupil dilation in terms of its appearance was the main factor Im a small engine...
View ArticleMAC 3216 Pumps Too Much Bar Oil
Hello MAC Chainsaw Gurus - I hope there are still some out there anyway. Two years ago I was given a MAC 3216 16" chainsaw that hadn't been used in some years; it appeared almost new. Checked it out...
View ArticleMS3616 bar mount studs loose.
Mine are loose, because I think the nuts have been tightened up too much. this saw has a plastic housing, into which the studs disappear. I cant tell how or what they are embedded into, but I can see...
View ArticleMcCULLOCH MAC 120 Chainsaw
I am not positive what model this is as the number stickers are gone. Could be a mini also. I just know it is a pain to rebuild carb ad you have to pull the entire motor out of the aluminum housing. I...
View ArticleMcCulloch FR56 parts
I have a couple of old McCulloch FR56 trimmers, that I bought over 15 years ago. They run great, and I use one for trimming the tall weeds at the edge of the property, and the other I keep a saw blade...
View Article96 McCulloch PowerMAC PM325AV-16 / looking for an oil tank
my McCulloch Chainsaw is Model # 600035-61 Serial # 11-024208 the oil tank I'm looking for is part number 300260 . Let me know if you have a oil tank for my chainsaw. Thanks
View Articlemac 15
Hello everyone! I have a vintage mac 15 and I am in need of a carb. Its a Tilliston HC 13 a
View ArticleNOS parts
Hey guys, I recently bought a bunch of NOS parts and find that I have 14 starter pulleys for 600 series saws. I posted them on eBay and priced them lower than any one else. Here is a link if you need...
View ArticleClik here to view.
My army of Pro-Macs and Timberman Saws
I noticed that no one has posted in this section in almost a year so I thought I would share some photos of my collection of hard working chain saw. They are heavy and mostly mad of metal there are...
View ArticleClik here to view.
mccullock 32cc line trimmer why wont the primer work!
Primer ball on my mccullock line trimmer will not pull gas from other side of the carb.. i really dont like the design and im not sure i fully understand how it actually works.. primer ball on the...
View ArticleClik here to view.
Need help identifying my TimberBear?
Hey guys, I got this McCulloch TimberBear for free from a customer who couldn't get it running. I took it home, replaced the clogged air filter, blew all the crud out of it, and adjusted the carb. Now...
View ArticleMcculloch Box of parts.........
Hello all, A friend of mine owns a outboard engine shop and used to be a Mcculloch dealer years ago. I mentioned to him that I needed a tensioner bolt for my Ms 38. He said I have a box of new parts...
View ArticleMcCulloch Pro mac 510
Looking for help reguarding a old saw my father in law used in the late 70s.He passed away last year and my mother in law wants me to get it running. The saw is a McCulloch pro mac 510 and not many...
View ArticleHello everyone can you help me identify this Mac?
I can't find a model number for this. Can anybody help me id please? Thanks
View Articlegearbox problem
Greetings! I bought a Mcculloch 165-107 model a few weeks ago. It was manufactured in 2013 and used the least in the previous owner. There is one problem in the gearbox. when he turns a small hill, the...
View ArticleCutting Deck cable forever breaking
Hello, I have a one year old mower tractor, M125-97TC which worked OK for last year, except for needing one new mower deck cable, but this year I have got through four cables. Within ten minutes of...
View ArticleBig Purchase
I bought 5 McCulloch' this week. I am a first time owner and I got motivated by watching Buckin Billy Ray and his saws lol. I picked up two 610's, Pro mac 55, Pro Mac 10-10A, Eager Beaver 2.0 , Very...
View ArticleMy mower starts but dies when putting into drive or cut
Hi, can anyone help? My ride on mower starts fine but dies if I let my foot off the clutch to drive it. It does the same if I try to put it into cut and the alarm to signify the box is full of grass...
View ArticleClik here to view.
Need oil pump for McCulloch eager Beaver 2.0 saw
I need a working oil pump for my McCulloch Eager Beaver 2.0 chain saw The label on the metal handle are hard to read. I need a oil pump and small hoses for this saw. Can someone direct me where to find...
View ArticleMcculloch T26 Trimmer won't start - ignition problem ?
I bougt a Mcculloch t26cs weed eater about two years ago. Only used ist about 10hours to now. Yesterday it worked good for about 10 minutes, then died while trimming with a puff sound. Won't start...
View ArticleMcCulloch fuel mixture
Hello, hoping someone can confirm the correct fuel/oil ratio. I found the info on http://www.acresinternet.com. It calls for a 40:1 ratio on my Pro Mac 700 & Pro Mac 610. The other night, I watched...
View ArticleBrake rod vibration and snapping
I have a M145-97TC and it is munching through brake rods on the cutting deck. I must have to remove the bits and replace it every 20 hours it feels like. The deck is serviced and has been balanced....
View ArticleMcCulloch Friction wheel
Hey all, Just wondering if anyone can tell me if they have a solution for a mcculoch mowcart 66 Friction Wheel I need. Part number -532 43 72-81. I have been told these frictionwheels are not able to...
View ArticleM51-140WR cutting height
Hi, I'm new to this forum as I have recently inherited a McCulloch M51-140WR. My question is about the cutting height. I have it on the lowest setting, and have taken the blade off and sharpened it -...
View ArticleTrim Mac 210 strimmer / trimmer fuel cap leaks from centre hole
I have an old Trim Mac 210 that I bought second hand a few years ago. This year it's started leaking fuel from the centre hole of the cap. It's not too bad with a small amount of fuel in the tank...
View ArticleMcCulloch B43 BT Strimmer: Spark plug change
Hi, I'm new to the forum and came here looking for help replacing the spark plug on my McCulloch strimmer. I have zero experience tinkering with engines so could really do with some idiot proof help...
View ArticleChainsaw won't fire
My McCulloch 130 (circa 1990) chainsaw was running fine and then just stopped. Now to will not fire at all. It used to start after one pull chocked and then one pull not chocked. Any idea where to...
View ArticleCan I gage raker teeth without a proper gage
My chain has been sharpened for years and years, and not by a person who is a good chain sharpener (me). I wonder, is it possible to tell if I should take a little off my rakers without using a proper...
View ArticleEducate me on 2 cycle oil please
McCulloch 130 instructions say to use McCulloch 2 cycle oil at 40:1 OR good 40 weight 2 cycle oil at 20:1. I have been using CountyLine 3.2 oz 40:1 2-Stroke Engine Oil and it has been working out well...
View ArticleBroken bar bolt-how to remove without breaking casting
McCulloch 130. Bolt that holds bar on is broken. I removed front of saw and removed gas tank to access it. The bolt will not come out. Apparently there are knurls on bolt to make to fit tight. How do I...
View ArticleClutch not disengaged?
McCulloch 130. I replaced bar bolt by removing front of engine enclosure and then removing gas tank. Now with it back together it seems that the clutch is not disengaged. I put the chain and bar on and...
View ArticleMcCulloch titan 30, 38cc carb help
i had purchased a Titan 30, the sticker on the plastic says that it is a 38cc chain saw, i had taken it apart to put a gasket kit in the carb and doing so i think i removed a vavle that was supposted...
View ArticleMcCulloch M46-500 lawn mower - what have I done wrong!?
Hello all i have recently bought a second hand McCulloch M46-500 which has a Briggs & Stratton series 500 engine. in using it for the first time, it started well, but as I went through more dense...
View ArticleMcCulloch MC 621 recoil string broken. Can you redo it ?
I have a McCulloch MC 621 single stage snow thrower . The rope on the recoil just broke ! I have done a couple of ropes on mowers, but can't figure out how to do this one ! IS it made to be ? It's part...
View ArticleClik here to view.
Zama carburetor identification
I have a McCulloch Eager Beaver IV 28cc 2-stroke blower with a Zama carb. I can't quite figure out Zama's model # for it to order the correct carb rebuild kit. I see that it's a C1U, but there are...
View ArticleChainsaw points ignition problem.
Just stopped running with no spark. Tried swap sparkplug. Troubleshooting, I checked the points gap, and resistance open infinite and 0 when closed- being i disconnected the ground and from the...
View ArticleMcCulloch 14.5 hp ride on
I need to change over my motor on my McCulloch 14.5hp ride on mower 2013 model, Briggs and Stratton. what is the next best size that will the same mounting
View ArticleMcCulloch M115577RB won’t start - electrical problem
After starting perfectly first time after the winter, after I stopped the engine after the first grass box fill up, I can’t get my mower restarted. Maybe I’m doing something daft having forgotten...
View ArticleLooking for a M19542 IPL
Got a McCulloch ride on that I am trying to find an IPL for Being sold in OZ it could very well be a mx of left over AYP parts 19.5 Intek engine 42" manual PTO deck 6 Speed manual transmission ( no id...
View ArticleMcCulloch Chain Saw 310 No Start !!!
So heres the story, Got this saw as a no start saw is in like new condition so thought it would be worth getting it back to running condition. For sure it did not start so this is what I have done....
View ArticleStarting problem when warm
I have a McCoullach 18 inch with BandS 450series 8 years old. Has always started easily cold or warm. Recently started to hunt running too rich. Changed diaphragm and gasket, now starts 1or 2 pulls...
View ArticleMcCulloch FR 56
Have been given a FR 56 McCulloch line trimmer. Missing the cover over the ignition on/off switch. Seem impossible to come across this piece. Is there any possibility of fitting another type ignition...
View ArticleManual Wanted
So I just picked up this Eager Beaver 2.0 chain saw looks in good shape but will need to go thru it to be sure. Model 12-062333 Ser. 60012312 can't seem to come up with the repair or owners manuals....
View ArticleFixed no run issue - Mcc 3616
I picked up a 14 year old Mcculloch 3616 (Husqvarna) for $10, I needed a smaller saw for fiddly bits. Replaced perished urethane fuel lines, air filter & a full cleanup & inspect. Looks to be...
View ArticleMcCulloch GBV 235 Leaf Blower Issue
Hi, I have a mcculoch leaf blower gbv 325. It wont start. The unusual thing is it has a spark and when I take the muffler of it fires.. doesn't run but repeatedly fires and sends smoke out. Yet when I...
View ArticleMcCulloch M155-107TC
I have the above sit on tractor mower and towards the end of the season last year it developed an issue where the drive belt would fall off when the cutting deck was disengaged, I put it down to an...
View ArticleNeed gas tank and carburetor for a McCullock Pro Mac Hedger Model #...
Need a gas tank with gas cap and a carburetor for a McCillock Pro Mac Hedger Model # TL20PVD-H7M. Or substitutes that would work just as well. Thanks. Bob Harper
View ArticleMcCulloch chainsaw - Titanium 420
Hi, Is anybody able to tell what the model is for the following please? It's from 1990'/2000's. It named Titanium 420 and has N213. But I cannot find any reference for it on the Web. Also, there is a...
View ArticleCompression testing a GBV345 leaf blower
Hi all. Is it possible to use an automotive compression tester on a small 25cc leaf blower motor, in this case a McCulloch GBV345 blower. I have heard that without a Schrader valve at the end of the...
View Article