Mcculloch T26 Trimmer won't start - ignition problem ?
I bougt a Mcculloch t26cs weed eater about two years ago. Only used ist about 10hours to now. Yesterday it worked good for about 10 minutes, then died while trimming with a puff sound. Won't start...
View ArticleMcCulloch fuel mixture
Hello, hoping someone can confirm the correct fuel/oil ratio. I found the info on http://www.acresinternet.com. It calls for a 40:1 ratio on my Pro Mac 700 & Pro Mac 610. The other night, I watched...
View ArticleBrake rod vibration and snapping
I have a M145-97TC and it is munching through brake rods on the cutting deck. I must have to remove the bits and replace it every 20 hours it feels like. The deck is serviced and has been balanced....
View ArticleMcCulloch Friction wheel
Hey all, Just wondering if anyone can tell me if they have a solution for a mcculoch mowcart 66 Friction Wheel I need. Part number -532 43 72-81. I have been told these frictionwheels are not able to...
View ArticleM51-140WR cutting height
Hi, I'm new to this forum as I have recently inherited a McCulloch M51-140WR. My question is about the cutting height. I have it on the lowest setting, and have taken the blade off and sharpened it -...
View ArticleTrim Mac 210 strimmer / trimmer fuel cap leaks from centre hole
I have an old Trim Mac 210 that I bought second hand a few years ago. This year it's started leaking fuel from the centre hole of the cap. It's not too bad with a small amount of fuel in the tank...
View ArticleMcCulloch B43 BT Strimmer: Spark plug change
Hi, I'm new to the forum and came here looking for help replacing the spark plug on my McCulloch strimmer. I have zero experience tinkering with engines so could really do with some idiot proof help...
View ArticleChainsaw won't fire
My McCulloch 130 (circa 1990) chainsaw was running fine and then just stopped. Now to will not fire at all. It used to start after one pull chocked and then one pull not chocked. Any idea where to...
View ArticleCan I gage raker teeth without a proper gage
My chain has been sharpened for years and years, and not by a person who is a good chain sharpener (me). I wonder, is it possible to tell if I should take a little off my rakers without using a proper...
View ArticleEducate me on 2 cycle oil please
McCulloch 130 instructions say to use McCulloch 2 cycle oil at 40:1 OR good 40 weight 2 cycle oil at 20:1. I have been using CountyLine 3.2 oz 40:1 2-Stroke Engine Oil and it has been working out well...
View ArticleBroken bar bolt-how to remove without breaking casting
McCulloch 130. Bolt that holds bar on is broken. I removed front of saw and removed gas tank to access it. The bolt will not come out. Apparently there are knurls on bolt to make to fit tight. How do I...
View ArticleClutch not disengaged?
McCulloch 130. I replaced bar bolt by removing front of engine enclosure and then removing gas tank. Now with it back together it seems that the clutch is not disengaged. I put the chain and bar on and...
View ArticleMcCulloch titan 30, 38cc carb help
i had purchased a Titan 30, the sticker on the plastic says that it is a 38cc chain saw, i had taken it apart to put a gasket kit in the carb and doing so i think i removed a vavle that was supposted...
View ArticleMcCulloch M46-500 lawn mower - what have I done wrong!?
Hello all i have recently bought a second hand McCulloch M46-500 which has a Briggs & Stratton series 500 engine. in using it for the first time, it started well, but as I went through more dense...
View ArticleMcCulloch MC 621 recoil string broken. Can you redo it ?
I have a McCulloch MC 621 single stage snow thrower . The rope on the recoil just broke ! I have done a couple of ropes on mowers, but can't figure out how to do this one ! IS it made to be ? It's part...
View ArticleClik here to view.
Zama carburetor identification
I have a McCulloch Eager Beaver IV 28cc 2-stroke blower with a Zama carb. I can't quite figure out Zama's model # for it to order the correct carb rebuild kit. I see that it's a C1U, but there are...
View ArticleChainsaw points ignition problem.
Just stopped running with no spark. Tried swap sparkplug. Troubleshooting, I checked the points gap, and resistance open infinite and 0 when closed- being i disconnected the ground and from the...
View ArticleMcCulloch 14.5 hp ride on
I need to change over my motor on my McCulloch 14.5hp ride on mower 2013 model, Briggs and Stratton. what is the next best size that will the same mounting
View ArticleMcCulloch M115577RB won’t start - electrical problem
After starting perfectly first time after the winter, after I stopped the engine after the first grass box fill up, I can’t get my mower restarted. Maybe I’m doing something daft having forgotten...
View ArticleLooking for a M19542 IPL
Got a McCulloch ride on that I am trying to find an IPL for Being sold in OZ it could very well be a mx of left over AYP parts 19.5 Intek engine 42" manual PTO deck 6 Speed manual transmission ( no id...
View Article